Technical Highlights
- Wi-Fi Standard: Supports IEEE 802.11 b/g/n with high throughput and stable TCP/IP performance
- Bluetooth Version: Bluetooth 5.x dual-mode (BR/EDR + BLE) with concurrent Wi-Fi + BT operation
- RF Co-existence: Advanced hardware-based co-existence ensuring minimal interference and reliable dual-radio performance
- Security: WPA3/WPA2/WPA support, AES hardware acceleration, secure boot, and OTA firmware upgrade capability
- Power Efficiency: Optimized power management with active, standby, and deep sleep modes for energy-efficient IoT designs
T2M9001
The T2M9001 Wi-Fi SoC is a high-performance 2.4 GHz wireless platform built for IEEE 802.11 b/g/n connectivity. It integrates the RF front end, PHY and MAC, a RISC-V processor, on-chip OTP, USB interface, and power management within a single compact chip. This high level of integration enables reliable wireless performance, reduced system complexity, and efficient power operation for a wide range of connected devices.
- Protocol: IEEE 802.11 b/g/n WLAN (1T1R, 20MHz)
- MCU: RISC-V CPU up to 160MHz
- SRAM: 224KB on-chip SRAM
- Flash: Embedded / External flash
- Rich Interface: USB 2.0 (up to 480Mbps), High-speed UART, 7× GPIO, Watchdog, GP Timers
- Supply Voltage: 3.3V supply integrated LDOs
- Security Mechanism: Encryption: Open / WEP40 / WEP104 / TKIP / AES128 (STA), Open / AES128 (AP). Authentication: WEP share-key / WPA / WPA2 (STA), WPA2 (AP)
Applications
- IP camera
- TV
- Set-top box
- Access point
- PC
Product Specifications
Product Selection Tool| Part No. | Protocol | MCU-MHz | SRAM (KB) | Flash (KB) | SPI | I2C | I2S | GPIO | UART | USB | ADC | Voltage | PKG | NODE |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| T2M9001A24 | Wi‑Fi 802.11 b/g/n | 160 | 224 | OTP 1 Kb | 1 | 1 | 0 | 7 | 1 | 1 | - | 3.3 V | 4x4 mm2, 24-pin QFN | 22nm |
T2M9001-M
The T2M9001-M is a highly integrated, high-performance 2.4 GHz Wi-Fi SoC module designed for reliable wireless LAN connectivity. The solution integrates the RF transceiver, IEEE 802.11 PHY and MAC layers, RISC-V processor, USB interface, and power management circuitry into a single chip, enabling compact and cost-efficient wireless designs.
The device supports IEEE 802.11 b/g/n standards with single spatial stream transmission over 20 MHz bandwidth, delivering stable throughput for embedded and IoT wireless applications.
Integrated RF components such as the power amplifier (PA), low-noise amplifier (LNA), transmit/receive switch, and balun reduce external component requirements and simplify system design while improving overall performance and reliability.
- Protocol: IEEE 802.11 b/g/n (2.4 GHz Wi-Fi), AP Mode, STA Mode
- MCU: RISC-V Processor, up to 160 MHz
- SRAM: 224 KB On-chip SRAM
- Flash: 128 KB On-chip ROM, 1 Kbit OTP Memory
- Rich Interface: USB 2.0 Interface
- Supply Voltage: 3.3 V
- Working Current: Dependent on Wi-Fi operating mode (TX/RX active operation supported as per 802.11 standards)
- Sleep Current: Low-power sleep mode supported (refer to power management operation)
-
Tx Maximum Power
- 17 ± 2 dBm @ 802.11b
- 15 ± 2 dBm @ 802.11g
- 14 ± 2 dBm @ 802.11n
- Rx Receive Sensitivity: Up to −92 dBm (1 Mbps)
- Security Mechanism: Standard Wi-Fi security protocols supported (WEP, WPA/WPA2)
Applications
- IoT devices
- Smart home equipment
- USB Wi-Fi dongles
- Embedded wireless terminals
- Industrial monitoring systems
- Consumer electronics
- Wireless data transmission devices
- Networked peripherals
- Smart appliances
- Connected sensors and controllers
Product Specifications
Product Selection Tool| Part No. | Protocol | MCU-MHz | SRAM (KB) | Flash (KB) | SPI | I2C | I2S | GPIO | UART | USB | ADC | Voltage | PKG | NODE |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| T2M9001M | - | 160 | - | - | - | - | - | - | - | - | - | - | - | - |
T2M9101
The T2M9101 Wi-Fi 6 SoC is a dual-band, dual-concurrent (DBDC) wireless platform designed for high-performance connectivity across 2.4 GHz and 5 GHz bands. It supports IEEE 802.11ax while maintaining compatibility with 802.11a/b/g/n/ac networks. Powered by four high-performance RISC-V processors, enabling high-speed data interfaces, flexible peripheral integration, and advanced RF and baseband performance for demanding wireless applications.
- Protocol: Wi-Fi 6 (802.11a/b/g/n/ac/ax) dual-band DBDC (2.4GHz + 5GHz), Bluetooth 5.3 (BT/BLE + BLE audio)
- MCU: Five high-performance 32-bit RISC-V CPUs
- SRAM: On-chip 136KB SRAM (DTOP) + 768KB Wi-Fi RAM + 210KB BT RAM
- Flash: Embedded / External flash (up to 16MB address space)
- Rich Interface: USB2.0, SDIO3.0 (slave), UART, SPI (master/slave), I2C (master/slave), I2S, GPIO
- Supply Voltage: VDD33: 2.97–3.63V, VDD18: 1.75–1.98V, VDD12/AVDD: 1.15–1.32V, VDD08: 0.75–0.98V
-
Working Current:
- Wi-Fi Transceiver DBDC: 280mA
- Wi-Fi 5G Transceiver: 160mA
- Wi-Fi 2G Transceiver: 140mA
-
Sleep Current:
- Wi-Fi DTIM: 1.0mA
- BT Sniff: 0.80mA
- TX Maximum Power: Wi-Fi 2.4GHz Tx power up to 21 dBm (MCS0) / Wi-Fi 5GHz up to 20 dBm (MCS0)
- RX Receive Sensitivity: Wi-Fi 2.4GHz: -101 dBm (11b 1Mbps) / BLE<: -101 dBm (LE 1M), -98 dBm (LE 2M)
- Security Mechanism: WPA/WPA2/WPA3, WEP, WAPI
Applications
- TVs
- Tablets
- PCs / Laptops
- Mobile phones
- Smart speakers
Product Specifications
Product Selection Tool| Part No. | Protocol | MCU-MHz | SRAM (KB) | Flash (KB) | SPI | I2C | I2S | GPIO | UART | USB | ADC | Voltage | PKG | NODE |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| T2M9101A126 | Wi‑Fi 802.11 b/g/n | 120 | 224 | OTP 1 Kb | 1 | 1 | 0 | 7 | 1 | 1 | - | 3.3 V | Not specified | 22nm |
T2M9118-M
The ML9118A-GAIA-M0-PG12 is a general-purpose wireless module supporting Wi-Fi 6, Bluetooth® Low Energy, and IEEE 802.15.4. It features a 32-bit RISC-V application processor (up to 160MHz) with embedded SRAM/ROM. The Wi-Fi subsystem includes a 2.4GHz radio with 802.11 b/g/n/ax PHY/MAC for low latency, longer range, and low power operation, along with a compact MCU that offloads processing tasks. The Bluetooth LE subsystem integrates the radio, modem, link controller, and Bluetooth Mesh, using the same MCU for firmware operation. In addition, the 2.4GHz radio supports 802.15.4, enabling Zigbee and Thread functionality.
- Protocol: Wi-Fi 6 (802.11 b/g/n/ax, 2.4GHz), Bluetooth® LE 5.4, IEEE 802.15.4 (Zigbee/Thread), Matter over Wi-Fi/Thread
- MCU: 32-bit RISC-V MCU (5-stage pipeline) up to 160MHz + dedicated 32-bit MCU for Wi-Fi/BLE
- SRAM: 576KB SRAM (includes up to 32KB AON SRAM)
- Flash: 4MB Flash (SiP)
- Rich Interface: GPIO (up to 19), UART, I2C, SPI, I2S, PWM, 12-bit ADC, SDIO 2.0 device, DMA
- Supply Voltage: 3.0V: 3.6V (typ. 3.3V)
-
Working Current:
- Wi-Fi TX: 159mA (11b/g @17dBm) / 142mA (11ax @15.5dBm)
- Wi-Fi RX: 50–58mA
- BLE TX: 95.4mA @0dBm / 136.7mA @10dBm
- BLE RX: 56mA
-
Sleep Current:
- Deep Sleep (retention): 90µA
- Hibernation: 64µA
-
TX Maximum Power:
- Wi-Fi TX power (typ): 17.4dBm (11g/n/ax)
- BLE TX (max setting): 15dBm
- 802.15.4 TX: 15dBm
-
RX Receive Sensitivity:
- Wi-Fi: -94dBm (11b 1Mbps)
- BLE: -95dBm (LE 1Mbps)
- 802.15.4: -98dBm (250kbps)
- Security Mechanism: Secure Boot, Flash encryption, AES-128/AES-256, SHA, RSA/ECC signature, TRNG
Applications
- Remote control
- Smart home devices
- Smart lighting devices
- AI audio
Product Specifications
Product Selection Tool| Part No. | Protocol | MCU-MHz | SRAM (KB) | Flash (KB) | SPI | I2C | I2S | GPIO | UART | USB | ADC | Voltage | PKG | NODE |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| T2M9118A40 | Wi-Fi 6 (802.11 b/g/n/ax), Bluetooth® LE 5.4, Zigbee 3.0, Thread, Matter | 160 | 576 | 4096 | 3 | 2 | 1 | 19 | 3 | 0 | 12 | 3.0 V – 3.6 V | 18.0 × 25.5 × 3.1 | 22nm |
T2M9201
The T2M9201 Wi-Fi chipset is built on WUQI’s proprietary dual-band RF architecture and advanced low-power CMOS power-amplifier technology, enabling simultaneous 2.4 GHz and 5 GHz operation (DBDC) with high efficiency. It delivers high data throughput, stable wireless links, and optimized power consumption, making it well suited for performance-driven devices such as Smartphones, Tablets, PCs, TVs, and Set-top boxes that require fast and reliable wireless connectivity.
- Protocol: Wi-Fi 6 (IEEE 802.11ax) + backward compatible 802.11a/b/g/n/ac, Dual-band DBDC (2.4GHz + 5GHz), Bluetooth 5.4 (BT/BLE, LE Audio)
- MCU: Five 32-bit RISC-V CPUs (Wi-Fi subsystem: 2 CPUs, DTOP: 2 CPUs, BT: 1 CPU)
- SRAM: On-chip SRAM includes: 136KB (DTOP) + 928KB (Wi-Fi subsystem RAM) + 98KB (Bluetooth subsystem RAM)
- Flash: Embedded / External flash (address space supports up to 16MB)
- Rich Interface: UART, I2C, SPI, I2S, GPIO, Watchdog, SDIO3.0, USB2.0
-
Supply Voltage:
- VDD33: 3.3V (2.97–3.63V)
- VDD18: 1.8V (1.75–1.98V)
- VDD12/AVDD: 1.2V (1.15–1.32V)
- VDD09: 0.8–0.9V (0.75–0.98V)
-
Working Current:
- Wi-Fi Transceiver DBDC: 280mA
- Wi-Fi 5G Transceiver: 160mA
- Wi-Fi 2G Transceiver: 140mA
-
Sleep Current:
- Wi-Fi DTIM: 1.0mA
- BT sniff: 0.80mA
- TX Maximum Power: Wi-Fi Tx power per chain: up to 20 dBm (2.4GHz, 802.11b 11Mbps)
- RX Receive Sensitivity: Wi-Fi Rx sensitivity: -99 dBm (2.4GHz, 802.11b 1Mbps, 1x1 20MHz)
- Security Mechanism: WPA/WPA2/WPA3, WEP, WAPI; HW security blocks include SHA, TRNG, RSA 4096, ECC
Applications
- Smartphones
- Tablets
- PCs / Laptops
- Televisions (Smart TV)
- Set-top boxes
Product Specifications
Product Selection Tool| Part No. | Protocol | MCU-MHz | SRAM (KB) | Flash (KB) | SPI | I2C | I2S | GPIO | UART | USB | ADC | Voltage | PKG | NODE |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| T2M9201A92 | Wi-Fi 6 (IEEE 802.11 a/b/g/n/ac/ax), Dual-Band DBDC 2.4 GHz & 5 GHz | 120 | 136 | upto 16 MB | 2 | 2 | 2 | 40 | 4 | 1 | - | 3.3 V / 1.8 V / 1.2 V / 0.8–0.9 V | QFN 9 × 7.5 | 22nm |
All Part Numbers
Global Search
| Series | Supplier Part No. | Protocol | MCU-MHz | SRAM (KB) | Flash (KB) | SPI | I2C | GPIO | USB | ADC | Datasheet |
|---|---|---|---|---|---|---|---|---|---|---|---|
| T2M9001 | T2M9001A24 | Wi‑Fi 802.11 b/g/n | 160 | 224 | OTP 1 Kb | 1 | 1 | 7 | 1 | - | N/A |
| T2M9001-M | T2M9001M | - | 160 | - | - | - | - | - | - | - | N/A |
| T2M9101 | T2M9101A126 | Wi‑Fi 802.11 b/g/n | 120 | 224 | OTP 1 Kb | 1 | 1 | 7 | 1 | - | N/A |
| T2M9118-M | T2M9118A40 | Wi-Fi 6 (802.11 b/g/n/ax), Bluetooth® LE 5.4, Zigbee 3.0, Thread, Matter | 160 | 576 | 4096 | 3 | 2 | 19 | 0 | 12 | N/A |
| T2M9201 | T2M9201A92 | Wi-Fi 6 (IEEE 802.11 a/b/g/n/ac/ax), Dual-Band DBDC 2.4 GHz & 5 GHz | 120 | 136 | upto 16 MB | 2 | 2 | 40 | 1 | - | N/A |