Description and Features
he 9528 combines the features and functions needed for high quality wireless audio into a single SoC. The 9518 supports standards and industrial alliance specifications including Bluetooth 5.2 including BDR/EDR, LE, indoor positioning and BLE Mesh, Zigbee 3.0, HomeKit, 6LoWPAN, Thread and 2.4GHz proprietary standard. The 9518 is designed to offer high integration, ultra-low power application capabilities. The 9518 integrates a powerful 32-bit RISC-V (RISC-Five) MCU, DSP, AI Engine, 2.4GHz ISM Radio, 256kB SRAM, 4MB Flash, stereo Audio Codec, 14bit Aux ADC, Analog and Digital Microphone input, PWM, flexible IO interfaces, and other peripheral blocks required for advanced audio applications. The 9518 also includes multi-stage power management design with sub-threshold level power consumption allowing ultra-low power operation and making it the ideal candidate for wearable and power-constraint applications. With the high integration level of 9518, few external components are needed to satisfy customers’ ultra-low cost requirements.
Features
Key features:
-
32-bit RISC-V microcontroller
-
Better power-balanced performance than ARM M4
-
Instruction and Data cache controller
-
Maximum running speed up to 96MHz
-
Memory architecture: up to 4MB Flash, 256kB SRAM including up to 64kB retention SRAM
-
Embedded AI Engine for audio processing
-
RTC and other timers:
-
Clock source of a 24MHz&32.768kHz Crystal and 32kHz/24MHz embedded RC oscillator
-
Three general 32-bit timers with four selectable modes in active mode
-
Watchdog timer
-
A low-frequency 32kHz timer available in low power mode
-
Interfaces:
-
Up to 44 GPIOs
-
2-wire JTAG interface
-
Flash I/F interface
-
Dual DMIC (Digital Mic), Dual AMIC (Analog Mic), 24bit 192kHz I2S
-
Stereo Audio Codec
-
SPI, I2C, USB 2.0, Swire, UART with hardware flow control and 7816 protocol support
-
Up to 6 channels of differential PWM
-
IR transmitter with DMA
-
One quadrature decoder (QDEC), two-phase input selectable
-
10-channel (only GPIO input), 14-bit Auxiliary ADC
-
Low power comparator
-
Embedded hardware AES and AES-CCM
-
Embedded Random Number Generator (TRNG)
-
Embedded hardware acceleration for Elliptical curve cryptography (ECC)
-
RF Features:
-
Bluetooth/802.15.4/2.4GHz RF transceiver in worldwide 2.4GHz ISM band
-
Bluetooth 5.2 Compliant, BLE 1Mbps and 2Mbps, Long Range 125kbps and 500kbps, BDR (Basic data rate), EDR (Enhanced data rate) 2Mbps and 3Mbps
-
IEEE802.15.4 compliant, 250kbps
-
2.4GHz proprietary 1Mbps/2Mbps/250kbps/500kbps mode with Adaptive Frequency Hopping feature
-
ANT mode
-
Rx Sensitivity: -96dBm@BLE 1Mbps, -93dBm@EDR 2Mbps mode, -100dBm@ IEEE802.15.4 250kbps
-
Tx output power: up to +10dBm @ BLE/BDR mode, +7dBm @ EDR mode
-
50 Ω matched single-pin antenna input
-
RSSI monitoring with +/-1dB resolution
-
Auto acknowledgement, retransmission and flow control
-
Support full-function BLE location features
-
Support PTA (Packet Traffic Arbitration) for Wi-Fi co-existence
-
Power Management
-
Power supply -VDD (battery): 1.8V~4.3V, VBUS (USB): 4.5V~5.5V
-
Low power controller by sub-threshold level power consumption Battery monitor for low battery voltage detection
-
Brownout detection/shutoff and Power-On-Reset
-
Multiple-power-state to optimize power consumption
-
Supports USB BC1.2 Battery Charging
-
Low power consumption:
-
Whole Chip, RX EDR mode: 5.23mA @ 4.2V DCDC
-
Whole Chip, TX BR mode: 5.34mA @ 0dBm, 4.2V DCDC
-
Whole Chip, TX EDR mode: 8.01mA @ 2.5dBm, 4.2V DCDC
-
Deep sleep with external wakeup (without SRAM retention): 0.4uA
-
Deep sleep with SRAM retention: < 1uA
-
Sub-threshold level power consumption for best energy efficiency
-
Bluetooth features Include:
-
Bluetooth support with BDR, EDR, and BLE 5.2
-
Long range support with 125kbps and 500kbps data rate
-
Bluetooth SIG Mesh support
-
Bluetooth ISO channel support (a.k.a Bluetooth 5.2) with broadcast and unicast mode
-
extended profile with audio support for voice command based searches
-
Wireless Audio features
-
High performance Stereo Audio Codec with SNR over 96dB and sampling rate up to 96kHz
-
24-bit ADC/DAC for Codec
-
Patented WA2+ technology for true wireless stereo and 1+N hearable devices with synchronized playback and balanced power on all devices
-
Support decoder for SBC, AAC, OPUS, LC3
-
Support voice codec such as G.711, A-Law, u-Law, CVSD, mSBC
-
Support HFP 1.7, HSP 1.2, A2DP 1.3, AVRCP 1.6, SPP 1.2, and PBAP 1.0, ANCS, DIS
-
Support Apple iAP2
-
Support EDR+BLE dual mode operation
-
Support noise suppression and echo cancellation
-
Support Packet Loss Concealment (PLC) for voice processing
-
Operating temperature range: -40℃~+85℃
-
Package Options: Completely RoHS-compliant package
-
T8259F1KET56, 56-pin QFN 7×7mm
-
T8259F1KET48, 48-pin QFN 7×7mm
-
T8259F1KET32, 32-pin QFN 5×5mm
Applications:
-
Wireless Headsets
-
Wireless Speakers
-
Hearables
-
Consumer Electronics